Engineering&Simulation Page 156

[img]http://www.ggu-software.com/software/ggu-laboratory/triaxial/druckversuch_1.gif[/img]The test data can be entered by hand, if wished, or imported as an ASCII file. After the input of all relevant parameters the test results can immediately be presented graphically on the screen. You can choose between different presentation forms and graphics:Tau-sigma diagram Stress paths Load-compression lines Pore water pressure-compression lines Stress ratio-compression lines Sigma 3-compression lines Volume-compression lines Protocol A MiniCAD system is available for additional labelling of graphics.Product:GGU Triaxial 3.13 Lanaguage:english Platform:Winxp/Win7 Size:1MB

[img]http://www.ggu-software.com/software/ggu-computation/transient/grundwassermodell_1.gif[/img]For a transient calculation of groundwater flow, a stable initial condition is required. This initial condition is found by the program GGU-TRANSIENT from a file (e.g. PLGW.DA1) which is created from a previous analysis undertaken with the program GGU-SS FLOW 2D. This data must be loaded as the first action after starting the program. In addition to the analysis results, the data file also contains the relevant soil and input parameters for the analysis.These fundamental parameters (e.g. k, neff etc.) cannot be modified in the GGU-TRANSIENT program. If they are altered, then the soil parameters will no longer match the potentials and flows, and the transient calculations will be meaningless. Of course, for all groundwater flow problems (planar vertical, planar...

In situ permeability from borehole pumping tests.The following evaluation methods after Cooper-Jacob are supported: :• Time-drawdown method• Distance-drawdown method• Distance-time-drawdown methodThe following evaluation methods after Theis are supported::• Type curves method• Recovery method Capabilities:Test planning Import from datalogger Import and export of ASCII data Graphics-orientated input, processing and result querying of measurement values Automatic compilation of system sketches Free design of output sheets Copying of image sections MiniCAD system for additional labelling of graphics [img]http://www.ggu-software.com/software/ggu-field/pumptest/pumpversuch_1.gif[/img]Product:GGU Pumptest v2.11 Lanaguage:English Platform:/WinNT/2000/XP Size:1MB

[img]http://www.ggu-software.com/software/ggu-computation/trench/schlitzwand_1.gif[/img]The GGU-TRENCH program allows the calculation and presentation of inner and outer stability of retaining wall laminae. For proof of stability of retaining wall laminae the following factors are calculated:Safety against groundwater ingress into the retaining wall trench Safety against slipage of single grains or grain groups Safety against subsurface slip planes endangering the retaining wall trench As data input is in accordance with Windows conventions it can be learnt almost without the use of a handbook. True-type fonts, colour output and bitmaps are supported.Product:GGU TRENCH 5.10 Lanaguage:english Platform:Winxp/Win7 Size:1.4MB

To create well logs. Utilising the possibility of data transfer with the drilled profile program GGU-STRATIG, you need only enter your horizon data once. The input of horizons can be carried out with user-defined abbreviations. The program can load and create the \”SEP” data format. An optically high quality output follows the data input.Product:GGU Borelog 4.14 Lanaguage:english Platform:Winxp/Win7 Size:2MB

Dimsoln Foundation3D 4. ::::::English Description::::::  Foundation3D is a spread and combined footing analysis/design tool that completes soil or pile supported foundation for industrial equipment such as horizontal exchanger, horizontal vessel, vertical vessel or tower, pipe racks and other miscellaneous plant design supports with minimal input. Allows multiple system of units for input and output – English, Metric and SI Supports ACI 318, BSI 8110, CSA A23.3 and IBC building codes Generates wind loads automatically for exchangers, vessels and towers based on ASCE recommendations Generates basic load combinations for equipment foundations automatically with just equipment geometry input Optimizes footing design (spread or combined) for an exchanger and horizontal vessel foundation depending on saddle to saddle dimensions and soil/pile criteria Considers buoyancy...

nd interpretation software package that runs on Geometrics seismographs or on your PC. Before you leave for the field, draw a geologic cross section of your site and conduct a simulated survey with sophisticated modeling software that shows you the best way to configure your survey.Change the model so you can see what is detectable. Identify first breaks quickly right on the seismograph with an accurate automatic picker with manual override or afterwards on your PC. Clean up noisy data with comprehensive filtering and view all your prior picks simultaneously for shot-to-shot coherence. Simulate a complete seismic refraction survey. Draw velocity cross sections, ray trace them and display the travel time curves. Handles lateral velocity variations, velocity inversions and blind...

RockWare DigiData is an inexpensive and easy to use program for on -screen digitizing. Use it to spot wells, collect elevation from a contour map, or digitize curve information from a raster log.Product:RockWare DigiData 2.0 Lanaguage:english Platform:Winxp/Win7 Size:4MB

Robust, fast and user-friendly tools are essential in geotechnical engineering. GeoDelft, the world-renowned Dutch geotechnical engineering and soil mechanics institute, realised this a long time ago. Since its foundation back in 1934, research and development at GeoDelft has been very important to the Netherlands, and as result GeoDelft is a world leader in Deltaic and soft soil/sediment environments. [img]http://www.delftgeosystems.nl/files/images_org/stormvloedkering.jpg[/img]Eastern Scheld storm surge barrier[b]Development:[/b]In the past 20 years, engineers and consultants at GeoDelft have profited from in-house software development. According to the specifications of experts, scientists, consultants and the industry, popular design and analysis tools were built for the Dutch Geo-Engineering industry. These products are now available in English for the international Geo-Engineering industry. Continuous development results in new products as...

Established in 1988, 12D Solutions sells and supports its principal product suite, 12d Model (formerly known as 4d Model) direct and through distributors around the world. 12D Solutions clients include civil and water engineering consultants;environmental consultants; surveyors; local; state and national government departments and authorities; research institutes; construction companies and mining consultants. 12d Model is a powerful terrain modelling, surveying and civil engineering software package. It allows fast production in a wide variety of projects including roads, rail, site layouts, and environmental impact studies.Product:12D MODEL 7.0 Lanaguage:english Platform:Winxp/Win7 Size:563MB